View ACH162244DGG_438907.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
74ALVCH162244 16-bit buffer/line driver with 30 termination resistor (3-State)
Product specification IC24 Data Handbook 1998 Jun 29
Philips Semiconductors
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30W termination resistor (3-State)
74ALVCH162244
FEATURES
* Wide supply voltage range of 1.2V to 3.6V * Complies with JEDEC standard no. 8-1A * CMOS low power consumption * MULTIBYTETM flow-through standard pin-out architecture * Low inductance multiple VCC and ground pins for minimum noise
and ground bounce
PIN CONFIGURATION
1OE 1Y0 1Y1 GND 1Y2 1Y3 VCC 2Y0 2Y1 1 2 3 4 5 6 7 8 9 48 2OE 47 1A0 46 1A1 45 GND 44 1A2 43 1A3 42 VCC 41 2A0 40 2A1 39 GND 38 2A2 37 2A3 36 3A0 35 3A1 34 GND 33 3A2 32 3A3 31 VCC 30 4A0 29 4A1 28 GND 27 4A2 26 4A3 25 3OE
* Direct interface with TTL levels * Bus hold on all data inputs * Integrated 30 termination resistor
DESCRIPTION
The 74ALVCH162244 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. The 74ALVCH162244 is a 16-bit non-inverting buffer/line driver with 3-State outputs. The device can be used as four 4-bit buffers, two 8-bit buffers or one 16-bit buffer. The 3-State outputs are controlled by the output enable inputs 1OE and 2OE. A HIGH on nOE causes the outputs to assume a high impedance OFF-state. The 74ALVCH162244 is designed with 30 series resistors in both HIGH and LOW output states. The 74ALVCH162244 has active bus hold circuitry which is provided to hold unused or floating data inputs at a valid logic level. This feature eliminates the need for external pull-up or pull-down resistors.
GND 10 2Y2 11 2Y3 12 3Y0 13 3Y1 14 GND 15 3Y2 16 3Y3 17 VCC 18 4Y0 19 4Y1 20 GND 21 4Y2 22 4Y3 23 4OE 24
SW00194
QUICK REFERENCE DATA
GND = 0 V; Tamb = 25C; tr = tf 2.5 ns SYMBOL tPHL/tPLH CI CPD PARAMETER Propagation delay An to Yn Input capacitance Power dissipation capacitance per buffer VI = GND to VCC1 Outputs enabled Outputs disabled CONDITIONS VCC = 2.5V, CL = 30pF VCC = 3.3V, CL = 50pF TYPICAL 3.0 2.7 5.0 25 4 UNIT ns pF pF
NOTES: 1. CPD is used to determine the dynamic power dissipation (PD in mW): PD = CPD x VCC2 x fi + S (CL x VCC2 x fo) where: fi = input frequency in MHz; CL = output load capacitance in pF; fo = output frequency in MHz; VCC = supply voltage in V; S (CL x VCC2 x fo) = sum of the outputs.
ORDERING INFORMATION
PACKAGES 48-Pin Plastic SSOP Type III 48-Pin Plastic TSSOP Type II TEMPERATURE RANGE -40C to +85C -40C to +85C OUTSIDE NORTH AMERICA 74ALVCH162244 DL 74ALVCH162244 DGG NORTH AMERICA ACH162244 DL ACH162244 DGG DWG NUMBER SOT370-1 SOT362-1
1998 Jun 29
2
853-2084 19638
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30W termination resistor (3-State)
74ALVCH162244
PIN DESCRIPTION
PIN NUMBER 1 2, 3, 5, 6 4, 10, 15, 21, 28, 34, 39, 45 7, 18, 31, 42 8, 9, 11, 12 13, 14, 16, 17 19, 20, 22, 23 24 25 30, 29, 27, 26 36, 35, 33, 32 41, 40, 38, 37 47, 46, 44, 43 48 SYMBOL 1OE 1Y0 to 1Y3 GND VCC 2Y0 to 2Y3 3Y0 to 3Y3 4Y0 to 4Y3 4OE 3OE 4A0 to 4A3 3A0 to 3A3 2A0 to 2A3 1A0 to 1A3 2OE Output enable input (active LOW) Data inputs Output enable input (active LOW) Output enable input (active LOW) Data outputs NAME AND FUNCTION Output enable input (active LOW) Data outputs Ground (0V) Positive supply voltage
FUNCTION TABLE
INPUTS nOE L L H H = HIGH voltage level L = LOW voltage level X = don't care Z = high impedance OFF-state nAn L H X OUTPUT nYn L H Z
LOGIC SYMBOL (IEEE/IEC)
1OE 2OE 3OE 4OE 1A0 1A1 1A2 1A3 2A0 1 48 25 24 47 46 44 43 41 1 40 38 37 36 35 33 32 30 29 27 26 1 4 1 3 2 EN1 EN2 EN3 EN4 1 1 2 3 5 6 8 9 11 12 13 14 16 17 19 20 22 23 1Y0 1Y1 1Y2 1Y3 2Y0 2Y1 2Y2 2Y3 3Y0 3Y1 3Y2 3Y3 4Y0 4Y1 4Y2 4Y3
LOGIC SYMBOL
1A0 47 2 1Y0 3A0 36 13 3Y0
2A1 2A2 2A3 3A0
1A1
46
3
1Y1
3A1
35
14
3Y1
3A1 3A2
1A2
44
5
1Y2
3A2
33
16
3Y2
3A3 4A0
1A3
43
6
1Y3
3A3
32
17
3Y3
4A1 4A2
1OE
1
3OE
25
4A3
SW00060
2A0 41 8 2Y0 4A0 30 19 4Y0
BUS HOLD CIRCUIT
VCC
2A1
40
9
2Y1
4A1
29
20
4Y1
2A2
38
11
2Y2
4A2
27
22
4Y2
2A3
37
12
2Y3
4A3
26
23
4Y3
2OE
48
4OE
24
Data Input
To internal circuit
SW00195
SW00044
1998 Jun 29
3
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30W termination resistor (3-State)
74ALVCH162244
RECOMMENDED OPERATING CONDITIONS
LIMITS SYMBOL PARAMETER DC supply voltage 2.5V range (for max. speed performance @ 30 pF output load) VCC DC supply voltage 3.3V range (for max. speed performance @ 50 pF output load) DC Input voltage range DC output voltage range Operating free-air temperature range Input rise and fall times VCC = 2.3 to 3.0V VCC = 3.0 to 3.6V CONDITIONS MIN 2.3 3.0 0 0 -40 0 0 MAX 2.7 V 3.6 VCC VCC +85 20 10 V V C ns/V UNIT
VI VO Tamb tr, tf
ABSOLUTE MAXIMUM RATINGS
In accordance with the Absolute Maximum Rating System (IEC 134) Voltages are referenced to GND (ground = 0V) SYMBOL VCC IIK VI IOK VO IO IGND, ICC Tstg PTOT PARAMETER DC supply voltage DC input diode current DC in ut voltage input DC output diode current DC output voltage DC output source or sink current DC VCC or GND current Storage temperature range Power dissipation per package -plastic medium-shrink (SSOP) -plastic thin-medium-shrink (TSSOP) For temperature range: -40 to +125 C above +55C derate linearly with 11.3 mW/K above +55C derate linearly with 8 mW/K VI t0 For data inputs with bus hold1 For control pins1 VO uVCC or VO t 0 Note 1 VO = 0 to VCC CONDITIONS RATING -0.5 to +4.6 -50 -0.5 to VCC +0.5 -0.5 to +4.6 "50 -0.5 to VCC +0.5 "50 "100 -65 to +150 850 600 UNIT V mA V mA V mA mA C mW
NOTE: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
1998 Jun 29
4
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30W termination resistor (3-State)
74ALVCH162244
DC ELECTRICAL CHARACTERISTICS
Over recommended operating conditions. Voltage are referenced to GND (ground = 0 V). LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40C to +85C MIN VIH HIGH level Input voltage VCC = 2.3 to 2.7V VCC = 2.7 to 3.6V LOW level Input voltage VCC = 2.3 to 2.7V VCC = 2.7 to 3.6V VCC = 2 3 to 3 6V; VI = VIH or VIL; IO = -100A 100A 2.3 3.6V; VCC = 2.3V; VI = VIH or VIL; IO = -4mA VCC = 2.3V; VI = VIH or VIL; IO = -6mA VOH HIGH level output voltage VCC = 2.7V; VI = VIH or VIL; IO = -4mA VCC = 2.7V; VI = VIH or VIL; IO = -8mA VCC = 3.0V; VI = VIH or VIL; IO = -6mA VCC = 3.0V; VI = VIH or VIL; IO = -12mA VCC = 2 3 to 3 6V; VI = VIH or VIL; IO = 100A 2.3 3.6V; VCC = 2.3V; VI = VIH or VIL; IO = 4mA VCC = 2.3V; VI = VIH or VIL; IO = 6mA VOL LOW level output voltage VCC = 2.7V; VI = VIH or VIL; IO = 4mA VCC = 2.7V; VI = VIH or VIL; IO = 8mA VCC = 3.0V; VI = VIH or VIL; IO = 6mA VCC = 3.0V; VI = VIH or VIL; IO = 12mA II IOZ ICC ICC IBHL2 g Input leakage current 3-State output OFF-state current Quiescent supply current Additional quiescent supply current Bus hold LOW sustaining current VCC = 2 3 to 3 6V; 2.3 3.6V; VI = VCC or GND VCC = 2.3 to 3.6V; VI = VIH or VIL; VO = VCC or GND VCC = 2.3 to 3.6V; VI = VCC or GND; IO = 0 VCC = 2.3V to 3.6V; VI = VCC - 0.6V; IO = 0 VCC = 2.3V; VI = 0.7V VCC = 3.0V; VI = 0.8V Bus hold HIGH sustaining current Bus hold LOW overdrive current Bus hold HIGH overdrive current VCC = 2.3V; VI = 1.7V VCC = 3.0V; VI = 2.0V VCC = 3.6V VCC = 3.6V 45 75 -45 -75 500 -500 -175 VCC*0.2 02 VCC*0.4 VCC*0.6 VCC*0.5 VCC*0.7 VCC*0.6 VCC*1.0 1.7 2.0 TYP1 1.2 V 1.5 1.2 1.5 VCC VCC*0.11 VCC*0.17 VCC*0.09 VCC*0.19 VCC*0.13 VCC*0.27 GND 0.07 0.11 0.06 0.13 0.09 0.19 0.1 0.1 0.2 150 - 150 0.20 0 20 0.40 0.55 0.40 0.60 0.55 0.80 5 10 40 750 A A A A A V V 0.7 V 0.8 MAX UNIT
VIL
IBHH2 IBHLO2 IBHHO2
A A A
NOTES: 1. All typical values are at Tamb = 25C. 2. Valid for data inputs of bus hold parts.
1998 Jun 29
5
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30W termination resistor (3-State)
74ALVCH162244
AC CHARACTERISTICS FOR VCC = 2.3V TO 2.7V RANGE AND VCC < 2.3V
GND = 0V; tr = tf 2.0ns; CL = 30pF SYMBOL LIMITS PARAMETER Propagation delay nAn to nYn 3-State output enable time nOE to nYn 3-State output disable time nOE to nYn WAVEFORM MIN tPHL/tPLH tPZH/tPZL tPHZ/tPLZ 1, 3 2, 3 2, 3 1.0 1.0 1.0 VCC = 2.3 to 2.7V TYP1 3.0 4.0 2.3 MAX 4.9 6.8 6.3 ns ns ns UNIT
NOTES: 1. All typical values are measured at Tamb = 25C and VCC = 2.5V.
AC CHARACTERISTICS FOR VCC = 3.0V TO 3.6V RANGE AND VCC = 2.7V
GND = 0V; tr = tf 2.5ns; CL = 50pF SYMBOL LIMITS PARAMETER Propagation delay nAn to nYn 3-State output enable time nOE to nYn 3-State output disable time nOE to nYn WAVEFORM VCC = 3.3 0.3V MIN tPHL/tPLH tPZH/tPZL tPHZ/tPLZ 1, 3 2, 3 2, 3 1.0 1.0 1.0 TYP1, 2 2.7 3.5 2.9 MAX 4.2 5.6 5.5 MIN 1.0 1.0 1.0 VCC = 2.7V TYP1 3.3 4.6 3.2 MAX 4.7 6.7 5.7 ns ns ns UNIT
NOTES: 1. All typical values are measured at Tamb = 25C. 2. Typical value is measured at VCC = 3.3V
1998 Jun 29
6
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30W termination resistor (3-State)
74ALVCH162244
AC WAVEFORMS FOR VCC = 2.3V TO 2.7V AND VCC < 2.3V RANGE
VM = 0.5 VCC VX = VOL + 0.15V VY = VOH -0.15V VOL and VOH are the typical output voltage drop that occur with the output load. V =V CC I
TEST CIRCUIT
VCC S1 2 * VCC Open GND
VI PULSE GENERATOR RT D.U.T.
VO
RL = 500
AC WAVEFORMS FOR VCC = 3.0V TO 3.6V AND VCC = 2.7V RANGE
VM = 1.5 V VX = VOL + 0.3V VY = VOH -0.3V VOL and VOH are the typical output voltage drop that occur with the output load. V = 2.7V I
VI An INPUT VM
CL
RL = 500
Test Circuit for switching times DEFINITIONS
RL = Load resistor CL = Load capacitance includes jig and probe capacitance RT = Termination resistance should be equal to ZOUT of pulse generators.
SWITCH POSITION
TEST tPLH/tPHL tPLZ/tPZL tPHL tPLH tPHZ/tPZH S1 Open 2 < VCC
GND
VCC < 2.7V 2.7-3.6V
VI VCC 2.7V
GND
VOH Yn OUTPUT VOL VM
SV00906
Waveform 3. Load circuitry for switching times
SW00057
Waveform 1. Input (An) to output (Yn) propagation delay times
VI nOE INPUT GND VM
tPLZ VCC OUTPUT LOW-to-OFF OFF-to-LOW VX VOL tPHZ VOH OUTPUT HIGH-to-OFF OFF-to-HIGH GND outputs enabled outputs disabled VY
tPZL
VM
tPZH
VM
outputs enabled
SW00058
Waveform 2. 3-State enable and disable times
1998 Jun 29
7
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30 termination resistor (3-State)
74ALVCH162244
SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm
SOT370-1
1998 Jun 29
8
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30 termination resistor (3-State)
74ALVCH162244
TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1mm
SOT362-1
1998 Jun 29
9
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30 termination resistor (3-State)
74ALVCH162244
NOTES
1998 Jun 29
10
Philips Semiconductors
Product specification
16-bit buffer/line driver with 30 termination resistor (3-State)
74ALVCH162244
Data sheet status
Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.
Production
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Date of release: 06-98 Document order number: 9397-750-04537
Philips Semiconductors
yyyy mmm dd 11

▲Up To Search▲

Price & Availability of ACH162244DGG

	To Download ACH162244DGG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .